A Review of Electric Vehicle Motors and Control Strategies 

Zineb Machhour, Abdelfattah Dani, Mhamed El Mrabet, Zineb Mekrini, Mohammed Khayat, Mohammed  Boulaala

Abstract


In the world where environmental protection and energy savings are growing concerns, the automotive industry is experiencing growing demand for automotive electrification. It was from the 2000s that the Electric Vehicle (EV) regained its momentum thanks to technological progress and ecological awareness. EV currently plays an important role in transportation, there are several types on the market such as battery electric vehicle (BEV), hybrid electric vehicle (HEV), plug-in hybrid electric vehicle (PHEV) and battery electric vehicle. Fuel cell. Vehicle (FCEV). Recently, all the interest of manufacturers in the automotive field has focused on the all-electric vehicle, thanks to its many advantages and its advantages granted to manufacturers, customers and especially the environment. The latter moves using one or more electric motors powered by a battery. This article will present the motors and control strategies most used by electric vehicle manufacturers and most studied by researchers, citing the principles advantages and disadvantages, and comparing them to be able to conclude what works best and the most sought after in automotive design.

Keywords


Electric Vehicle (EV), Brushless DC Motor (BLDC), Switched Reluctance Motor (SRM), Finite Control Set Model Predictive Control (FCS-MPC), Model Predictive Contouring Control (MPCC).

Full Text:

PDF

References


A. T. Cabrera, J. A. Aguado Sánchez, M. Longo, and F. Foiadelli, “Sensitivity analysis of a bidirectional wireless charger for EV,” 2016 IEEE International Conference on Renewable Energy Research and Applications (ICRERA), Birmingham, UK, pp. 1113–1116, 2016. doi: 10.1109/ICRERA.2016.7884506.

M. Brenna, M. Longo, D. Zaninelli, R. Miceli, and F. Viola, “CO2 reduction exploiting RES for EV charging,” 2016 IEEE International Conference on Renewable Energy Research and Applications (ICRERA), Birmingham, UK, pp. 1191–1195, 2016. doi: 10.1109/ICRERA.2016.7884521.

D. Mohanraj, J. Gopalakrishnan, B. Chokkalingam, and L. Mihet-Popa, “Critical aspects of electric motor drive controllers and mitigation of torque ripple - Review,” IEEE Access, vol. 10, pp. 73635–73674, 2022. doi: 10.1109/ACCESS.2022.3187515.

A. K. Basu, S. Tatiya, and S. Bhattacharya, “Overview of electric vehicles (EVs) and EV sensors,” in Overview of Electric Vehicles (EVs) and EV Sensors, Springer, Singapore, 2019. doi: 10.1007/978-981-13-3290-6_7.

C. Liu, C. Jiang, and C. Qiu, “Overview of coil designs for wireless charging of electric vehicle,” 2017 IEEE PELS Workshop on Emerging Technologies: Wireless Power Transfer (WoW), 2017. doi: 10.1109/WoW.2017.7959389.

C. Liu, K. T. Chau, C. H. T. Lee, and Z. Song, “A critical review of advanced electric machines and control strategies for electric vehicles,” Proceedings of the IEEE, vol. 109, no. 6, pp. 1004–1028, 2021. doi: 10.1109/JPROC.2020.3041417.

D. G. Dorrell, A. M. Knight, M. Popescu, L. Evans, and D. A. Staton, “Comparison of different motor design drives for hybrid electric vehicles,” IEEE Energy Conversion Congress and Exposition (ECCE), pp. 3352–3359, 2010. doi: 10.1109/ECCE.2010.5618318.

K. T. Chau and W. Li, “Overview of electric machines for electric and hybrid vehicles,” International Journal of Vehicle Design, vol. 64, no. 1, pp. 46–71, 2014. doi: 10.1504/IJVD.2014.057775.

M. G. Simoes and P. Vieira, “A high torque low-speed multi-phase brushless machine: A perspective application for electric vehicles,” IECON 2000, vol. 1, pp. 1395–1400, 2000. doi: 10.1109/IECON.2000.972325.

N. Hashemnia and B. Asaei, “Comparative study of using different electric motors in the electric vehicles,” 2008 International Conference on Electrical Machines, 2008. doi: 10.1109/ICELMACH.2008.4800157.

A. Damiano, C. Musio, and I. Marongiu, “Experimental validation of a dynamic energy model of a battery electric vehicle,” 2015 International Conference on Renewable Energy Research and Applications (ICRERA), Palermo, Italy, pp. 803–808, 2015. doi: 10.1109/ICRERA.2015.7418523.

J. W. Jiang, B. Bilgin, and A. Emadi, “Three-phase 24/16 switched reluctance machine for a hybrid electric powertrain,” IEEE Transactions on Transportation Electrification, vol. 3, no. 1, pp. 76–85, 2017. doi: 10.1109/TTE.2017.2664778.

P. P. Acarnley and J. F. Watson, “Review of position-sensorless operation of brushless permanent-magnet machines,” IEEE Transactions on Industrial Electronics, vol. 53, no. 2, pp. 352–362, 2006. doi: 10.1109/TIE.2006.870868.

C. Liu, K. T. Chau, D. Wu, and S. Gao, “Opportunities and challenges of vehicle-to-home, vehicle-to-vehicle, and vehicle-to-grid technologies,” Proceedings of the IEEE, vol. 101, no. 11, pp. 2409–2427, 2013. doi: 10.1109/JPROC.2013.2271951.

R. Asghar, F. Rehman, Z. Ullah, A. Qamar, K. Ullah, K. Iqbal, A. Aman, and A. A. Nawaz, “Electric vehicles and key adaptation challenges and prospects in Pakistan: A comprehensive review,” Journal of Cleaner Production, vol. 278, 2021. doi: 10.1016/j.jclepro.2020.123375.

M. Zeraoulia, M. E. H. Benbouzid, and D. Diallo, “Electric motor drive selection issues for HEV propulsion systems: A comparative study,” IEEE Transactions on Vehicular Technology, vol. 55, no. 6, pp. 1756–1764, 2006. doi: 10.1109/TVT.2006.878719.

R. Cao, C. Mi, and M. Cheng, “Quantitative comparison of flux-switching permanent-magnet motors with interior permanent magnet motor for EV, HEV, and PHEV applications,” IEEE Transactions on Magnetics, vol. 48, no. 8, pp. 2374–2384, 2012. doi: 10.1109/TMAG.2012.2190614.

B. Tanç, H. T. Arat, E. Baltac?o?lu, and K. Ayd?n, “Overview of the next quarter century vision of hydrogen fuel cell electric vehicles,” International Journal of Hydrogen Energy, vol. 44, no. 20, pp. 10120–10128, 2019. doi: 10.1016/j.ijhydene.2018.10.112.

C. Mahmoudi, A. Flah, and L. Sbita, “An overview of electric vehicle concept and power management strategies,” 2014 International Conference on Electrical Sciences and Technologies in Maghreb (CISTEM), 2014. doi: 10.1109/CISTEM.2014.7077026.

P. K. H. Dost, P. Spichartz, and C. Sourkounis, “Charging behavior of users utilizing battery electric vehicles and extended range electric vehicles within the scope of a field test,” IEEE Transactions on Industry Applications, vol. 54, no. 1, pp. 580–590, 2018. doi: 10.1109/TIA.2017.2758753.

A. Karki, S. Phuyal, D. Tuladhar, S. Basnet, and B. P. Shrestha, “Status of pure electric vehicle power train technology and future prospects,” Applied System Innovation, vol. 3, no. 3, pp. 1–28, 2020. doi: 10.3390/asi3030035.

S. J. Rind, M. Jamil, and A. Amjad, “Challenges faced by electric vehicle motors and their solutions,” 2018 53rd International Universities Power Engineering Conference (UPEC), 2018. doi: 10.1109/UPEC.2018.8541871.

A. M. Omekanda, “Switched reluctance machines for EV and HEV propulsion: State-of-the-art,” 2013 IEEE Workshop on Electrical Machines Design, Control and Diagnosis (WEMDCD), pp. 70–74, 2013. doi: 10.1109/WEMDCD.2013.6525166.

F. He, G. Xie, and J. Luo, “Electrical bearing failures in electric vehicles,” Friction, vol. 8, no. 1, pp. 4–28, 2020. doi: 10.1007/s40544-019-0356-5.

H. El Hadraoui, M. Zegrari, A. Chebak, O. Laayati, and N. Guennouni, “A multi-criteria analysis and trends of electric motors for electric vehicles,” World Electric Vehicle Journal, vol. 13, no. 4, pp. 1–28, 2022. doi: 10.3390/wevj13040065.

P. Bhatt, H. Mehar, and M. Sahajwani, “Electrical motors for electric vehicle – A comparative study,” SSRN Electronic Journal, 2019. doi: 10.2139/ssrn.3364887.

K. S. Mohammad and A. S. Jaber, “Comparison of electric motors used in electric vehicle propulsion system,” Indonesian Journal of Electrical Engineering and Computer Science, vol. 27, no. 1, pp. 11–19, 2022. doi: 10.11591/ijeecs.v27.i1.pp11-19.

C. Liu, K. T. Chau, J. L. Kirtley, C. C. Chan, K. Rajashekara, M. Cheng, T. M. Jahns, Z. Zhang, B. Kwon, J. Shek, W. Li, A. Garrigós, C. H. T. Lee, H. Komurcugil, A. Banerjee, M. Ehsani, S. Gao, A. Chiba, A. Tessarolo, A. M. Cramer, and M. M. Amin, “Guest editorial emerging electric machines and drives for smart energy conversion,” IEEE Transactions on Energy Conversion, vol. 33, no. 4, pp. 1931–1933, 2018. doi: 10.1109/TEC.2018.2879231.

H. Tu, H. Feng, S. Srdic, and S. Lukic, “Extreme fast charging of electric vehicles: A technology overview,” IEEE Transactions on Transportation Electrification, vol. 5, no. 4, pp. 861–878, 2019. doi: 10.1109/TTE.2019.2958709.

A. B. Yildiz, “Electrical equivalent circuit based modeling and analysis of direct current motors,” International Journal of Electrical Power & Energy Systems, vol. 43, no. 1, pp. 1043–1047, 2012. doi: 10.1016/j.ijepes.2012.06.063.

I. Suwarno, Y. Finayani, R. Rahim, J. Alhamid, and A. R. Al-Obaidi, “Controllability and observability analysis of DC motor system and a design of FLC-based speed control algorithm,” Journal of Robotics and Control, vol. 3, no. 2, pp. 227–235, 2022. doi: 10.18196/jrc.v3i2.10741.

W. Cai, X. Wu, M. Zhou, Y. Liang, and Y. Wang, “Review and development of electric motor systems and electric powertrains for new energy vehicles,” Automotive Innovation, vol. 4, no. 1, pp. 3–22, 2021. doi: 10.1007/s42154-021-00139-z.

A. El Ghaly, “Simplified control for torque and speed ripple mitigation in brushless DC motors,” vol. 8, no. 1, 2024.

K. T. Chau, D. Zhang, J. Z. Jiang, C. Liu, and Y. Zhang, “Design of a magnetic-geared outer-rotor permanent-magnet brushless motor for electric vehicles,” IEEE Transactions on Magnetics, vol. 43, no. 6, pp. 2504–2506, 2007. doi: 10.1109/TMAG.2007.893714.

M. Bahrami, H. Mokhtari, and A. Dindar, “Energy regeneration technique for electric vehicles driven by a brushless DC motor,” IET Power Electronics, vol. 12, no. 13, pp. 3397–3402, 2019. doi: 10.1049/iet-pel.2019.0024.

L. Vido, “Etude d’actionneurs electriques à double excitation destinés au transport. Dimensionnement de structures synchrones,” 2004. [Online]. Available: https://tel.archives-ouvertes.fr/tel-00477166/document

J. Gu, M. Ouyang, J. Li, D. Lu, C. Fang, and Y. Ma, “Driving and braking control of PM synchronous motor based on low-resolution hall sensor for battery electric vehicle,” Chinese Journal of Mechanical Engineering, vol. 26, no. 1, pp. 1–10, 2013. doi: 10.3901/CJME.2013.01.001.

Z. Wang, T. W. Ching, S. Huang, H. Wang, and T. Xu, “Challenges faced by electric vehicle motors and their solutions,” IEEE Access, vol. 9, pp. 5228–5249, 2021. doi: 10.1109/ACCESS.2020.3045716.

A. Murali, R. S. Wahab, C. S. R. Gade, C. Annamalai, and U. Subramaniam, “Assessing finite control set model predictive speed controlled PMSM performance for deployment in electric vehicles,” World Electric Vehicle Journal, vol. 12, no. 1, 2021. doi: 10.3390/wevj12010041.

R. G. Shriwastava, M. P. Thakre, K. V. Bhadane, M. S. Harne, and N. B. Wagh, “Performance enhancement of DCMLI fed DTC-PMSM drive in electric vehicle,” Bulletin of Electrical Engineering and Informatics, vol. 11, no. 4, pp. 1867–1881, 2022. doi: 10.11591/eei.v11i4.3714.

A. Katkout, T. Nasser, and A. Essadki, “Robust multiobjective model predictive control with computation delay compensation for electric vehicle applications using PMSM with multilevel inverter,” Mathematical Problems in Engineering, vol. 2020, 2020. doi: 10.1155/2020/7015865.

D. Kim, H. Hwang, S. Bae, and C. Lee, “Analysis and design of a double-stator flux-switching permanent magnet machine using ferrite magnet in hybrid electric vehicles,” IEEE Transactions on Magnetics, vol. 52, no. 7, pp. 10–13, 2016. doi: 10.1109/TMAG.2016.2532360.

M. A. Rakesh Kumar and S. Padmanaban, “Electric vehicles for India: Overview and challenges,” IEEE India Info, vol. 14, no. 2, pp. 139–142, 2019.

K. W. E. Cheng, “Recent development on electric vehicles,” 2009 3rd International Conference on Power Electronics Systems and Applications (PESA), 2009.

Z. Yang, F. Shang, I. P. Brown, and M. Krishnamurthy, “Comparative study of interior permanent magnet, induction, and switched reluctance motor drives for EV and HEV applications,” IEEE Transactions on Transportation Electrification, vol. 1, no. 3, pp. 245–254, 2015. doi: 10.1109/TTE.2015.2470092.

H. K. Khan, A. Al Rakib, and S. Nazmi, “Design and performance evaluation of numerical relay for three-phase induction motor protection,” International Journal of Smart Grid, vol. 7, no. 2, 2023. doi: 10.20508/ijsmartgrid.v7i2.272.g259.

S. Sharifan, S. Ebrahimi, A. Oraee, and H. Oraee, “Performance comparison between brushless PM and induction motors for hybrid electric vehicle applications,” pp. 719–724, 2016. doi: 10.1109/optim.2015.7492473.

B. Tabbache, M. E. H. Benbouzid, A. Kheloui, and J. M. Bourgeot, “Virtual-sensor-based maximum-likelihood voting approach for fault-tolerant control of electric vehicle powertrains,” IEEE Transactions on Vehicular Technology, vol. 62, no. 3, pp. 1075–1083, 2013. doi: 10.1109/TVT.2012.2230200.

T. Zou, D. Gerada, A. La Rocca, M. Moslemin, A. Cairns, M. Cui, A. Bardalai, F. Zhang, and C. Gerada, “A comprehensive design guideline of hairpin windings for high power density electric vehicle traction motors,” IEEE Transactions on Transportation Electrification, vol. 8, no. 3, pp. 3578–3593, 2022. doi: 10.1109/TTE.2022.3149786.

X. D. Xue, K. W. E. Cheng, and N. C. Cheung, “Selection of electric motor drives for electric vehicles,” Australasian Universities Power Engineering Conference (AUPEC), 2008.

C. M. Burt, X. Piao, F. Gaudi, B. Busch, and N. F. Taufik, “Electric motor efficiency under variable frequencies and loads,” Journal of Irrigation and Drainage Engineering, vol. 134, no. 2, pp. 129–136, 2008. doi: 10.1061/(ASCE)0733-9437(2008)134:2(129).

N. Abdelfatah, H. Abdeldjebar, I. Bousserhane, S. Hadjeri, and P. Sicard, “Two wheel speed robust sliding mode control for electric vehicle drive,” Serbian Journal of Electrical Engineering, vol. 5, no. 2, pp. 199–216, 2008. doi: 10.2298/sjee0802199a.

C. M. Spargo, B. C. Mecrow, J. D. Widmer, and C. Morton, “Application of fractional-slot concentrated windings to synchronous reluctance motors,” IEEE Transactions on Industry Applications, vol. 51, no. 2, pp. 1446–1455, 2015. doi: 10.1109/TIA.2014.2341733.

M. Yildirim, M. Polat, and H. Kurum, “A survey on comparison of electric motor types and drives used for electric vehicles,” 16th International Power Electronics and Motion Control Conference and Exposition (PEMC), pp. 218–223, 2014. doi: 10.1109/EPEPEMC.2014.6980715.

H. Kärkkäinen, L. Aarniovuori, M. Niemelä, J. Pyrhönen, and J. Kolehmainen, “Technology comparison of induction motor and synchronous reluctance motor,” IECON 2017 - 43rd Annual Conference of the IEEE Industrial Electronics Society, pp. 2207–2212, 2017. doi: 10.1109/IECON.2017.8216371.

M. Takeno, A. Chiba, N. Hoshi, S. Ogasawara, M. Takemoto, and M. A. Rahman, “Test results and torque improvement of the 50-kW switched reluctance motor designed for hybrid electric vehicles,” IEEE Transactions on Industry Applications, vol. 48, no. 4, pp. 1327–1334, 2012. doi: 10.1109/TIA.2012.2199952.

S. S. Ramamurthy and J. C. Balda, “Sizing a switched reluctance motor for electric vehicles,” IEEE Transactions on Industry Applications, vol. 37, no. 5, pp. 1256–1264, 2001. doi: 10.1109/28.952500.

A. Pina Ortega, “Design and comparison of induction motor and synchronous reluctance motor for variable speed applications: Design aided by differential evolution and finite element analysis,” 2011.

C. Gan, Y. Chen, R. Qu, Z. Yu, W. Kong, and Y. Hu, “An overview of fault-diagnosis and fault-tolerance techniques for switched reluctance machine systems,” IEEE Access, vol. 7, pp. 174822–174838, 2019. doi: 10.1109/ACCESS.2019.2956552.

P. B. Reddy, A. M. El-Refaie, S. Galioto, and J. P. Alexander, “Design of synchronous reluctance motor utilizing dual-phase material for traction applications,” IEEE Transactions on Industry Applications, vol. 53, no. 3, pp. 1948–1957, 2017. doi: 10.1109/TIA.2017.2661719.

M. Tadjuddin, I. Hasanuddin, Z. Fuadi, A. Mukminin, and M. R. Arief, “Power density comparison of multi-air gap axial flux permanent magnet motor for electric vehicle,” IOP Conference Series: Materials Science and Engineering, vol. 931, no. 1, p. 012007, 2020. doi: 10.1088/1757-899X/931/1/012007.

A. T. De Almeida, F. T. E. Ferreira, and J. A. C. Fong, “Standards for efficiency of electric motors: Permanent magnet synchronous motor technology,” IEEE Industry Applications Magazine, vol. 17, no. 1, pp. 12–19, 2011. doi: 10.1109/MIAS.2010.939427.

M. Ellims and H. E. Monkhouse, “Agonising over ASILs: Controllability and the in-wheel motor,” IET Conference Publications, vol. 2012, no. 607 CP, 2012. doi: 10.1049/cp.2012.1524.

R. Palanisamy, R. Sahasrabuddhe, M. K. Hiteshkumar, and J. A. Puranik, “A new energy regeneration system for a BLDC motor driven electric vehicle,” International Journal of Electrical and Computer Engineering, vol. 11, no. 4, pp. 2986–2993, 2021. doi: 10.11591/ijece.v11i4.pp2986-2993.

Q. Wang and S. Niu, “Overview of flux-controllable machines: Electrically excited machines, hybrid excited machines and memory machines,” Renewable and Sustainable Energy Reviews, vol. 68, pp. 475–491, 2017. doi: 10.1016/j.rser.2016.09.098.

M. Z. Ahmad, E. Sulaiman, Z. A. Haron, and T. Kosaka, “Design improvement of a new outer-rotor hybrid excitation flux switching motor for in-wheel drive EV,” 2013 IEEE 7th International Power Engineering and Optimization Conference (PEOCO), pp. 298–303, 2013. doi: 10.1109/PEOCO.2013.6564561.

C. Bae, T. Koo, Y. Son, K. Park, J. Jung, S. Han, and M. Suh, “A study on reliability centered maintenance planning of a standard electric motor unit subsystem using computational techniques,” Journal of Mechanical Science and Technology, vol. 23, no. 4, pp. 1157–1168, 2009. doi: 10.1007/s12206-009-0305-8.

T. Hadden et al., “A review of shaft voltages and bearing currents in EV and HEV motors,” IECON 2016, pp. 1578–1583, 2016. doi: 10.1109/IECON.2016.7793357.

D. Staton, A. Boglietti, and A. Cavagnino, “Solving the more difficult aspects of electric motor thermal analysis,” IEEE International Electric Machines and Drives Conference (IEMDC), vol. 2, pp. 747–755, 2003. doi: 10.1109/IEMDC.2003.1210320.

S. Kaleg, A. Hapid, and M. R. Kurnia, “Electric vehicle conversion based on distance, speed and cost requirements,” Energy Procedia, vol. 68, pp. 446–454, 2015. doi: 10.1016/j.egypro.2015.03.276.

N. de Assis Brasil Weber, B. P. da Rocha, P. Smith Schneider, L. C. Daemme, and R. de Arruda Penteado Neto, “Energy and emission impacts of liquid fueled engines compared to electric motors for small size motorcycles based on the Brazilian scenario,” Energy, vol. 168, pp. 70–79, 2019. doi: 10.1016/j.energy.2018.11.051.

M. Ehsani, Y. Gao, and J. M. Miller, “Hybrid electric vehicles: Architecture and motor drives,” Proceedings of the IEEE, vol. 95, no. 4, pp. 719–728, 2007. doi: 10.1109/JPROC.2007.892492.

S. Gherairi, “Zero-emission hybrid electric system: Estimated speed to prioritize energy demand for transport applications,” International Journal of Smart Grid-ijSmartGrid, vol. 3, no. 4, 2019. doi: 10.20508/ijsmartgrid.v3i4.76.g65.

M. Yilmaz, “Limitations/capabilities of electric machine technologies and modeling approaches for electric motor design and analysis in plug-in electric vehicle applications,” Renewable and Sustainable Energy Reviews, vol. 52, pp. 80–99, 2015. doi: 10.1016/j.rser.2015.07.033.

P. Gonzalez, G. Buigues, and A. J. Mazon, “Noise in electric motors: A comprehensive review,” Energies, vol. 16, no. 14, 2023. doi: 10.3390/en16145311.

J. F. Gieras, C. Wang, and J. C. Lai, Noise of Polyphase Electric Motors, 2005. doi: 10.1201/9781420027730.

I. Ibrahim, R. Silva, M. H. Mohammadi, V. Ghorbanian, and D. A. Lowther, “Surrogate-based acoustic noise prediction of electric motors,” IEEE Transactions on Magnetics, vol. 56, no. 2, pp. 1–4, 2020. doi: 10.1109/TMAG.2019.2945407.

H. Chuan, S. M. Fazeli, Z. Wu, and R. Burke, “Mitigating the torque ripple in electric traction using proportional integral resonant controller,” IEEE Transactions on Vehicular Technology, vol. 69, no. 10, pp. 10820–10831, 2020. doi: 10.1109/TVT.2020.3013414.

L. De Novellis, A. Sorniotti, P. Gruber, L. Shead, V. Ivanov, and K. Hoepping, “Torque vectoring for electric vehicles with individually controlled motors: State-of-the-art and future developments,” World Electric Vehicle Journal, vol. 5, pp. 617–628, 2012.

H. K. Araz and M. Y?lmaz, “Design procedure and implementation of a high-efficiency PMSM with reduced magnet-mass and torque-ripple for electric vehicles,” Journal of the Faculty of Engineering and Architecture of Gazi University, vol. 35, no. 2, pp. 1089–1109, 2020. doi: 10.17341/gazimmfd.458515.

O. M. Vasilevskyi, “Metrological characteristics of the torque measurement of electric motors,” International Journal of Metrology and Quality Engineering, vol. 8, pp. 1–9, 2017. doi: 10.1051/ijmqe/2017005.

O. Wasynczuk, S. D. Sudhoff, K. A. Corzine, J. L. Tichenor, P. C. Krause, I. G. Hansen, and L. M. Taylor, “A maximum torque per ampere control strategy for induction motor drives,” IEEE Transactions on Energy Conversion, vol. 13, no. 2, pp. 163–169, 1998. doi: 10.1109/60.678980.

K. T. Chau, “Overview of energy systems for electric and hybrid vehicles,” in Energy Systems for Electric and Hybrid Vehicles, pp. 1–30, 2016. doi: 10.1049/pbtr002e_ch1.

B. Tabbache, N. Rizoug, M. E. H. Benbouzid, and A. Kheloui, “A control reconfiguration strategy for post-sensor FTC in induction motor-based EVs,” IEEE Transactions on Vehicular Technology, vol. 62, no. 3, pp. 965–971, 2013. doi: 10.1109/TVT.2012.2232325.

P. Han, M. Cheng, and Z. Chen, “Dual-electrical-port control of cascaded doubly-fed induction machine for EV/HEV applications,” IEEE Transactions on Industry Applications, vol. 53, no. 2, pp. 1390–1398, 2017. doi: 10.1109/TIA.2016.2625770.

D. Mohanraj, R. Aruldavid, R. Verma, K. Sathiyasekar, A. B. Barnawi, B. Chakhalingam, and L. Mihet-Popa, “A review of BLDC motor: State of art, advanced control techniques, and applications,” IEEE Access, vol. 10, pp. 54833–54869, 2022. doi: 10.1109/ACCESS.2022.3175011.

G. Wang, M. Valla, and J. Solsona, “Position sensorless permanent magnet synchronous machine drives - A review,” IEEE Transactions on Industrial Electronics, vol. 67, no. 7, pp. 5830–5842, 2020. doi: 10.1109/TIE.2019.2955409.

A. M. Trzynadlowski, Z. Wang, J. M. Nagashima, C. Stancu, and M. H. Zelechowski, “Comparative investigation of PWM techniques for a new drive for electric vehicles,” IEEE Transactions on Industry Applications, vol. 39, no. 5, pp. 1396–1403, 2003. doi: 10.1109/TIA.2003.816555.

C. Liu and Y. Luo, “Overview of advanced control strategies for electric machines,” Chinese Journal of Electrical Engineering, vol. 3, no. 2, pp. 53–61, 2017. doi: 10.23919/CJEE.2017.8048412.

G. H. B. Foo and X. Zhang, “Robust direct torque control of synchronous reluctance motor drives in the field-weakening region,” IEEE Transactions on Power Electronics, vol. 32, no. 2, pp. 1289–1298, 2017. doi: 10.1109/TPEL.2016.2542241.

D. Mande, J. P. F. Trovão, M. C. Ta, and T. Van Do, “Dual-source bidirectional quasi-Z-source inverter development for off-road electric vehicles,” World Electric Vehicle Journal, vol. 13, no. 9, 2022. doi: 10.3390/wevj13090174.

M. Salehifar, M. Moreno-Eguilaz, G. Putrus, and P. Barras, “Simplified fault tolerant finite control set model predictive control of a five-phase inverter supplying BLDC motor in electric vehicle drive,” Electric Power Systems Research, vol. 132, pp. 56–66, 2016. doi: 10.1016/j.epsr.2015.10.030.

A. Raisemche, M. Boukhnifer, and D. Diallo, “New fault-tolerant control architectures based on voting algorithms for electric vehicle induction motor drive,” Transactions of the Institute of Measurement and Control, vol. 38, no. 9, pp. 1120–1135, 2016. doi: 10.1177/0142331215587717.

E. Picotti, M. Bruschetta, E. Mion, and A. Beghi, “A nonlinear model-predictive contouring controller for shared control driving assistance in high-performance scenarios,” IEEE Transactions on Systems, Man, and Cybernetics: Systems, vol. 53, no. 1, pp. 204–215, 2023. doi: 10.1109/TSMC.2022.3177271.

U. R. Muduli, A. R. Beig, R. K. Behera, K. Al Jaafari, and J. Y. Alsawalhi, “Predictive control with battery power sharing scheme for dual open-end-winding induction motor based four-wheel drive electric vehicle,” IEEE Transactions on Industrial Electronics, vol. 69, no. 6, pp. 5557–5568, 2022. doi: 10.1109/TIE.2021.3091919.

H. Heidari, A. Rassolkin, A. Kallaste, T. Vaiman, E. Andriushchenko, A. Belahcen, and D. V. Lukichev, “A review of synchronous reluctance motor-drive advancements,” Sustainability, vol. 13, no. 2, pp. 1–37, 2021. doi: 10.3390/su13020729.

U. R. Muduli, K. Al Jaafari, R. K. Behera, A. R. Beig, and J. Y. Alsawalhi, “Predictive control based battery power sharing for four-wheel drive electric vehicle,” IEEE Applied Power Electronics Conference and Exposition (APEC), pp. 817–821, 2021. doi: 10.1109/APEC42165.2021.9487084.

U. R. Muduli, K. Al Jaafari, R. K. Behera, A. R. Beig, K. Al Hosani, and J. Y. Alsawalhi, “Predictive battery SoC control for dual propulsion differential four wheel drive electric vehicle,” IEEE Energy Conversion Congress and Exposition (ECCE), pp. 1490–1495, 2021. doi: 10.1109/ECCE47101.2021.9595587.

J. Kabzan, L. Hewing, A. Liniger, and M. N. Zeilinger, “Learning-based model predictive control for autonomous racing,” IEEE Robotics and Automation Letters, vol. 4, no. 4, pp. 3363–3370, 2019. doi: 10.1109/LRA.2019.2926677.

Z. Machhour, M. El Mrabet, Z. Mekrini, and M. Boulaala, “Comparative study between DTC and FOC control strategies applied to the BLDC motor: A review,” in International Conference on Advanced Intelligent Systems for Sustainable Development (AI2SD’2023), Lecture Notes in Networks and Systems, vol. 930, pp. 262–271, Springer, Cham, 2024. doi: 10.1007/978-3-031-54318-0_22.




DOI (PDF): https://doi.org/10.20508/ijrer.v16i2.15333.g9217

Refbacks

  • There are currently no refbacks.


Online ISSN: 1309-0127

Publisher: Gazi University

IJRER is indexed in EI Compendex, SCOPUS, EBSCO, WEB of SCIENCE (Clarivate Analytics)and CrossRef.

IJRER has been indexed in Emerging Sources Citation Index from 2016 in web of science.

WEB of SCIENCE in 2025; 

h=35,

Average citation per item=6.59

Last three Years Impact Factor=(1947+1753+1586)/(146+201+78)=5286/425=12.43

Category Quartile:Q4